View BD9756AMWV_4665088.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/4
STRUCTURE PRODUCT SERIES TYPE PIN ASSIGNMENT BLOCK DIAGRAM PACKAGE Functions
Silicon Monolithic Integrated Circuit 7-Channel Switching Regulator Controller for Digital Camera
BDAMWV
Fig.1 Fig.1 Fig.2
1.5V minimum input operating Supplies power for the internal circuit by using charge-pump circuit which outputs a voltage twice bigger than VBATvoltage. or a equal voltage as VBAT + VIN. Contains step-up converter(1ch), step-down converter(2ch), cross converter(1ch), configurable for step-up/step-down converter(1ch), with PWM brightness controller for step-up converter(1ch). Contains 4FETs for the cross converter channe.l 3channels contain transistor for synchronous rectifying action mode. 2channels contain FETs for the step-up converter. All channels contain internal compensation between inputs outputs of error amps. Contains sequence control circuit for ch1,2 and 4. Operating frequency 1.2MHz(CH14), 600kHz(CH57). Contains output interception circuit when over load. 2 channels have high side switches with soft start function, one channel has PMOS back gate control circuit. Thermally enhanced UQFN044V6060 package.(6mm x 6mm, 0.4mm pitch)
Absolute maximum ratings (Ta=25)
Parameter Power Supply Boltage Symbol VBAT VHx14 Power Input Voltage HS67H VLx67 VIN IomaxLx1 Output Current IomaxHx2 IomaxHx34 IomaxHS67 IomaxLx67 Pd Topr Tstg Tjmax Limits 0.37 0.37 0.37 0.320 -0.37 1.2 1.5 1.2 1.2 0.8 0.54 *1 25+85 55+150 +150 Units V V V V V A A A A A W
Power Dissipation Operating Temperature Storage Temperature Junction Tempareture
(*1) Without external heat sink, the power dissipation reduces by 4.32mW/ over 25
Recommended operating conditions
Parameter Power Supply Voltage VREF Pin Connecting Capacitor VREGA Pin Connecting Capacitor SCP Pin Connecting Capacitor C+H to C+L connecting Capacitor Oscillator Oscillator Frequency OSC Timing Resistor Symbol VBAT CVREF CVREGA CSCP CF fosc RT MIN 1.5 0.47 0.47 1.0 0.6 47 Spec TYP 1.0 1.0 1.2 62 MAX 5.5 4.7 4.7 0.47 1.5 120 Unit V F F F F MHz k
Status of this document The Japanese version of this document is the official specification. Please use the translation version of this document as a reference to expedite understanding of the official version. If these are any uncertainty in translation version of this document, official version takes priority.
REV. B
2/4 Electrical characteristics Ta=25, VBAT=3V, RT=62k, STB16=3V,PWM7=2.5V
Parameter Symbol MIN 5.2 4.5 Standard value TYP MAX 5.4 4.8 50 90 2.6 2.30 200 0.54 170 6 1.1 Units Conditions Parameter Output Driver CH1 Highside SW ON Resistance CH1 Lowside SW ON Resistance CH2 LX21Pin Highside SW ON Resistance CH2 LX21Pin Lowside SW ON Resistance CH2 LX22Pin Highside SW ON Resistance CH2 LX22Pin Lowside SW ON Resistance CH3 Highside SW ON Resistance CH3 Lowside SW ON Resistance CH4 Highside SW ON Resistance CH4 Lowside SW ON Resistance CH6 NMOS SW ON Resistance CH6,7 Load SW ON Resistance CH5 Driver Output Voltage H Symbol Min Standard value TYP MAX 160 130 160 380 180 240 Units Conditions
Charge Pump Circuit Output Voltage Vcpout1 (Regulated) Output Voltage ( X2 Step up) Vcpout2
V V kHz V V V mA V mV A V
Io=1mA,, INV17=1.2V NON5= -0.2V Only for internal Current VBAT=2.5V, INV17=1.2V NON5= -0.2V CF=1F, VBAT=2.5V RT=62k
RON1P RON1N RON21P
m m m
HX1=3V, CPOUT=5.4V CPOUT=5.4V HX2=3.0V, CPOUT=5.4V CPOUT=5.4V
Output Vcpro 35 Resistance Operating fcp 60 75 Frequency Minimum VBAT Vst1 1.5 Voltage Internal Regulator VREGA Output Voltage VREGA 2.4 2.5 Prevention Circuit of Miss Operation by Low voltage Input Threshold Voltage Vstd1 2.15 Hysteresis Width Vstd1 50 100 Short Circuit Protection Timer start Vtcinv 0.42 0.48 threshold voltage SCP Stand by Vssc 22 Voltage SCP Out Source Iscp 2 4 Current SCP Threshold Vscp 0.9 1.0 Voltage Oscillator Frequency fosc1 1.0 1.2 CH14 Frequency fosc2 0.5 CH57 Max Duty Dmax1d 1,3,4Step Down Max Duty Dmax1u 86 1,4Step Up Max Duty 5,6,7 Dmax2 86 Max Duty Dmax3 CH2 LX21 Max Duty Dmax4 78 CH2 LX22 Error AMP Input Biias Current IINV INV Threshold VINV1 0.79 Voltage1 INV Threshold VINV2 0.99 Voltage2 INV Threshold VINV3 513 Voltage3 Base Bias Voltage Vref for inverted Channel CH5 VOUT5 -6.09 OutputVoltage Line Regulation DVLi Output Current Ios 0.2 When shorted Soft Start CH1,2,4 Tss1,2,4 1.5 Soft Start Time CH3 Tss3 0.5 Soft Start Time CH5 Tss5 1.5 Soft Start Time CH6 Tss6 2.0 Soft Start Time CH7 Tss7 4.7 Soft Start Time 0.6 92 92 84 0 0.80 1.00 540
RON21N
130
200
m
RON22P
180
280
m
VOUT2=5.0V
Io=5mA VREGA Monitor
RON22N RON3P RON3N RON4P RON4N RON6N RON67P Vout5H

PVCC5 -1.5
130 160 130 280 130 500 200
PVCC5 -1.0
200 260 200 380 200 800 300 1.0
m m m m m m m V V
CPOUT=5.4V HX3=3.0V, CPOUT=5.4V CPOUT=5.4V HX4=5.0V CPOUT=5.4V CPOUT=5.4V HS67H=3.0V CPOUT=5.4V IOUT5=50mA, NON5=0.2V, PVCC5=3V IOUT5=50mA, NON5=0.2V
INV monitor CH4
Vscp=0.1V
1.4 0.7 100 96 96 100 90 50 0.81 1.01 567
MHz MHz % % % % % nA V V mV
RT=62k RT=62k Vscp=0V (1)
CH5 Driver Vout5L Output Voltage L Switch to configure step up/down
UDSEL4 Control Voltage Step down Step up
CPOUT x0.7
0.5
VUDDO VUDUP VSTBH1 VSTBL1 RSTB1 VPWMH1 VPWML1 RPWM1 ISTB1 ISTB2 ISTB3 ISTB4
400 50
CPOUT CPOUT x0.3
V V V V k V V k A A A A
INV17=1.2V, NON5=-0.2V, VBAT=3.0V Step -down UDSEL1,4=CPOUT Step-up UDSEL1,4=0V
0 1.5 -0.3 250 1.5 0 30
STB16
STB control Voltage Active Non Active
5.5 0.3 700 4.0 0.4 80 5 5 5 5
INV17, NON5=3.0V CH14 CH6, 7V CH7I NON5 resistor12k, 72k (2) CPOUT=1.55.5V Vref=0V
Pull down Resistance PWM7
PWM7 control Voltage Active Non Active
Pull down Resistance Circuit Current
VBAT terminal HX terminal LX terminal HS67H terminal
-6.00 4.0 1.0
-5.91 12.5
V mV mA
Stand-by Current
2.5 1.5 2.5 3.0 5.7
3.5 2.5 3.5 4.0 6.7
msec msec msec msec msec
RT=62k RT=62k RT=62k RT=62k RT=62k
Circuit Current1 (VBAT current when voltage supplied for the terminal) Circuit Current2 (CPOUT current when voltage supplied for the terminal)
Icc1
7.0
11.0
mA
Icc2
3.0
5.0
mA
INV17=1.2V, NON5=-0.2V, CPOUT=5.4V
C+H, C+L=OPEN
(1)The protective circuit start working when circuit is operated by 100% duty. So it is possible to use only for transition time shorter than charge time for SCP. (2)Recommend resistor value over 20k between VREF to NON5, because VREF current is under 100uA. This product is not designed for normal operation with in a radioactive environment
REV. B
3/4
CPOUT
VREGA
Pin Assignment Block Diagram
VREF
33
VBAT
32
31
30
29
28
27
26
25
24
INV1
23 REF 0.8V + + + +
PRE DRIVER
GND
1.0V VREF
CHARGE PUMP 2.5V REG UVLO TSD
OSC
NON5 INV6 INV7 INV7I PWM7 HS6L HS67H HS7L Lx7 PGND567 Lx6
REF 0V 34 35 36 37 38 50k 39
+
SCP
SCP
C+H
C+L
VIN
RT
REF + 1.0V REF + 1.0V +
REF 0.8V REF 0.8V REF 0.8V
B.G.CTL
22 21 20 19 18 17 16
INV3 INV2 INV4 Hx4 Lx4 PGND4 Hx2 Lx21 PGND2 Lx22 VOUT2
DAC
OCP
PWM & LOGIC BLOCK
PRE DRIVER
HI-SIDE SW
40 41
OCP
OCP
15 14 13
42 43 44 PRE DRIVER PRE DRIVER PRE DRIVER
400k 400k
PRE DRIVER
PRE DRIVER 12
400k
1
2
3
4
5
6
7
8
9
10
11
STB124
STB56
OUT5
PVCC5
STB3
Hx1
Hx3
Lx1
Lx3
PGND13
UDSEL4
Fig. 1
Pin Description
Pin Name VBAT VIN CPOUT GND C+H C+L PGND13,2,4,567 VREGA VREF PVCC5 Description Input for battery voltage Returning voltage from output terminal Output terminal for Charge Pump Ground terminal Terminal for connecting flying capacitor for Charge Pump(H side) Terminal for connecting flying capacitor for Charge Pump(L side) Ground terminal for internal FET VREGA output CH5 base bias voltage CH5 PMOS VCC input for driver
Pin Name OUT5 Hx1,3,4 Lx1,3,4,6,7 Hx2 Lx21 Lx22 VOUT2 HS67H HS6L,HS7L INV1,2,3,4,6,7 NON5
Description Terminal for connecting gate of CH5 PMOS Input terminal for synchronous High side switch, Power supply for Pch Driver Terminal for connecting inductors Power supply for channel 2 Terminal for connecting inductor for CH2 input Terminal for connecting inductor for CH2 output CH2 output voltage Power supply for internal load switch Output terminal for internal load switch Error AMP inverted input Error AMP non-inverted input
Pin Name INV7I RT SCP UDSEL4 STB124,3,56 PWM7
Description Error AMP inverted input For connecting a resistor to set the OSC frequency For connecting a capacitor to set up the delay time of the SCP Step-up/down switching mode selection(H: step-down, L:step-up) ON/OFF switch H: operating over 1.5V ON/OFF switch Duty input for PWM brightness control
Package
BD9756MW
A
LOT No. Fig. 2
REV. B
4/4
Operation Notes
.) Absolute maximum ratings This product is produced with strict quality control. However, the IC may be destroyed if operated beyond its absolute maximum ratings. If the device is destroyed by exceeding the recommended maximum ratings, the failure mode will be difficult to determine. (E.g. short mode, open mode) Therefore, physical protection counter-measures (like fuse) should be implemented when operating conditions beyond the absolute maximum ratings anticipated. .) GND potential Make sure GND is connected at lowest potential. All pins except NON5, must not have voltage below GND. Also, NON5 pin must not have voltage below - 0.3V on start up. .) Setting of heat Make sure that power dissipation does not exceed maximum ratings. .) Pin short and mistake fitting Avoid placing the IC near hot part of the PCB. This may cause damage to IC. Also make sure that the output-to-output and output to GND condition will not happen because this may damage the IC. .) Actions in strong magnetic field Exposing the IC within a strong magnetic field area may cause malfunction. .) Mutual impedance Use short and wide wiring tracks for the main supply and ground to keep the mutual impedance as small as possible. Use inductor and capacitor network to keep the ripple voltage minimum. .) Voltage of STB pin The threshold voltages of STB pin are 0.3V and 1.5V. STB state is set below 0.3V while action state is set beyond 1.5V. The region between 0.3V and 1.5V is not recommended and may cause improper operation. The rise and fall time must be under 10msec. In case to put capacitor to STB pin, it is recommended to use under 0.01F. .) Thermal shutdown circuit (TSD circuit) The IC incorporates a built-in thermal shutdown circuit (TSD circuit). The thermal shutdown circuit (TSD circuit) is designed only to shut the IC off to prevent runaway thermal operation. It is not designed to protect the IC or guarantee its operation. Do not continue to use the IC after operating this circuit or use the IC in an environment where the operation of this circuit is assumed. .)Rush current at the time of power supply injection. An IC which has plural power supplies, or CMOS IC could have momentary rush current at the time of power supply injection. Please take care about power supply coupling capacity and width of power Supply and GND pattern wiring. .)IC Terminal Input This IC is a monolithic IC that has a P- board and P+ isolation for the purpose of keeping distance between elements. A P-N junction is formed between the P-layer and the N-layer of each element, and various types of parasitic elements are then formed. For example, an application where a resistor and a transistor are connected to a terminal (shown in Fig.15): When GND > (terminal A) at the resistor and GND > (terminal B) at the transistor (NPN), the P-N junction operates as a parasitic diode. When GND > (terminal B) at the transistor (NPN), a parasitic NPN transistor operates as a result of the NHayers of other elements in the proximity of the aforementioned parasitic diode. Parasitic elements are structurally inevitable in the IC due to electric potential relationships. The operation of parasitic elements Induces the interference of circuit operations, causing malfunctions and possibly the destruction of the IC. Please be careful not to use the IC in a way that would cause parasitic elements to operate. For example, by applying a voltage that is lower than the GND (P-board) to the input terminal.
Resistor Terminal A
Transistor (NPN) B Terminal B C
E GND Terminal Parasitic element N GND
P N N P-board
P
P N Parasitic element
P N
P P-board
P
Parasitic element
GND
Fig - 3 Simplified structure of a Bipolar IC
REV. B

N
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com (c) 2009 ROHM Co., Ltd. All rights reserved.
R0039A

▲Up To Search▲

Price & Availability of BD9756AMWV

	To Download BD9756AMWV Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .